CAN I SET UP A BATHTUB MYSELF? FACTORS TO CONSIDER AS WELL AS ACTIONS

Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions

Can I Set Up a Bathtub Myself? Factors to Consider As Well As Actions

Blog Article

Explore Now

Just how do you feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?


Tools You Need to Install a New Bathtub
Mounting a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the task can relocate immediately; if you need to open up a wall surface to eliminate the old bathtub as well as position the new bathtub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to vacate the old bathtub as well as set in the new one. See to it you have certified on your own for the work as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is much better to think about employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have currently purchased a new bathtub and also don't need to transform the plan of your previous supply of water pipes.
Your devices as well as material list must make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted access that is usually the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
    Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
    If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Installing the Tub


    Utilizing both wood boards under its feet, position the bathtub in the required position. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
    The next goal is to make sure that the tub is leveled all round. This can be attained by examining the level and changing the feet on the tub up until the spirit level checks out level.
    To set up taps, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the very same for the various other faucet.
    Activate the water and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill up the tub and also check the overflow electrical outlet and also the regular electrical outlet for leakages.
    Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the tub has been used at the very least when as this will certainly settle it into its last placement.

    Getting ready for the Setup


    Firstly, the supporting structure provided with the bath should be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
    Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washers.
    Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be fitted in its last setting.

    Tiling Around the Tub


    In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and possible leakages to the ceiling below.
    You can select from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly load the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not take into account this movement prior to securing.
    Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    We had been made aware of that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through a friend on our other web page. Are you aware of another person who is enthusiastic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Please feel free to promote it. We truly appreciate reading our article about How to Install a Bathtub Yourself.




    Book A Service Call


    Report this page